Excavator Hydraulic Breaker Hammer Chisel
Deskripsyon sa mga produkto
1.Materyal nga:40Cr o 42CrMo
2.Dimensyon:Depende sa espesipikasyon sa Tool Maker
3.Tipo sa chisel:Moil Point, Blunt Tool, Flat, wedge
4.Pagtambal sa init:
Austenting Temperatura 810~850 (20min/pulgada)
Pagpabugnaw sa Tubig Pagpabugnaw sa lana
Tempering 250~300 (1hr/pulgada)
5.Mekanikal nga mga kabtangan:
Katig-a sa nawong HRC51± 3
Kinatibuk-ang Katig-a HRC35± 3
Kusog sa tensile(min) 1250N/mm²
Punto sa abot (min) 950N/mm²
Elongation 10~14%
Pagkunhod sa Lugar 35~40%
Epekto nga trabaho 23~28 ft1b
Gidak-on sa lugas 7.0~8.0
Pagputos ug Pagpadala
Disenyo ug istruktura
Kami adunay hydraulic breaker chisel alang sa mosunod nga mga butang
| Krupp | HM45,HM50/60,HM60/75,HM85,HM130/135,HM170/185,HM200,HM300/301, |
| HM400/401,HM550,HM560CS,HM580,HM600/601,HM700 | |
| RAMMER | S21,S20/22,ROX100,S23,S25,S26/,ROX400,S29,S52/,ROX700, |
| S54/700,S55,S56/800,S82/1400 | |
| NPK | H1XA,H2XA,H3XA,H4X,H6XA,H7X,H8XA,H10XA |
| INDECO | MES350,HB5,MES553,MES621,MES1200,HB12,HB19,MES1800,HB27,MES2500 |
| MONTABERT | BRH30,BRH40,BRH45,BRH60,BRH76/91,BRP100,BRP130,BRP125,BRH250, |
| RH501,BRH620, BRH625,BRH750,BRV32 | |
| STANLEY | MB125,MB250/350,MB550,MB656,MB800,MB1550, |
| MB1950/1975, MB30EX, MB40EX | |
| FURUKAWA | HB05R,HB1G,HB2G,HB3G,HB5G,HB8G,HB10G,HB15G,HB20G |
| HB30G, HB40G, HB50G, | |
| TOKU/TOYO | TNB1E, TNB2E, TNB4E, TNB6E, TNB7E, TNB14E, TNB22EA, THBB101, |
| OKADA | OUB301,OUB302,OUB303,OUB305,OUB308,OUB310,OUB312,OUB316,OUB318, |
| SOOSAN | SB10,SB20,SB30,SB35,SB40,SB43,SB45,SB50,SB60,SB70,SB81, |
| SB100,SB121,SB130,SB151 | |
| KWANGLIM | SG200,SG300,KSG350,SG400,SG600,SG800,SG1200,SG1800,SG2100,SG2500, |
| DAEMO | DMB03,DMB04,DMB06,S150-V,S300-V,S500-V,S700-V,S900-V,S1300-V,S1800-V |
| HANWOO | RHB301,RHB302,RHB303,RHB304,RHB305,RHB306,RHB308,RHB309,RHB313, |
| DAINONG | D30,D50,D60,D70/90,D110,D130,D160,T180,K20 |
| K25,K30,K50,K80,K120,K55S,K40S, |
Materyal nga
